Share your best way to hook up subs and amp can

Subwoofers are typically easy to connect, given that there are usually only two cords to deal with: one for power and one for the audio input. You're far more likely to spend the bulk of time positioning and adjusting a subwoofer for the best performance than actually plugging in a pair of cables. However, not all subwoofers are so simple and straightforward, depending on the specific model and maybe some personal experience. If your receiver or amplifier has enough variety, you should be able to handle most any subwoofer out there. Almost all home theater receivers or processors and some stereo receivers have this type of subwoofer output. It's usually just one cable with single RCA connectors on both ends.

Mar 23,   My question is what is the best way to connect the subwoofer to the receiver. There are plenty of options: A. Through a RCA cable B. Through Surround L/R into the subwoofer with L/R being output through the subwoofer. C. Parallel wire hookup, where I tap into the L/R surround channels directly from the receiver to the subwoofer. The best way to connect the sub is to get a subwoofer with a high level input and then run a set of speaker cables from the output of your receiver or power amplifier to those inputs. Subs today are generally powered so no need to get a passive one and I'd recommend against that. You would need to set the main speakers to "large" in the receiver or pre-amp set-up menu. If you have both LFE and sub out connections on a receiver or preamp, your best choice would be to use the 'sub out' connector, because the LFE signal may still be mixed in with the sub channel.

Peak Power Output watts Min. Impedance Unbridged 2 ohms Min. Impedance Bridged 4 ohm What is the Best way to hook the two subs up?

Answer Save. How many ohms are they and what can your amp handle? For series speakers, just add the resistance together.

all personal

You can mix and match these equations to get the right impedance required by your amp. You should use a capacitor as well.

still variants? opinion

Recommend for every watts MAX you use a. Likewise, an "RCA cable" is a misnomer.

Apr 14,   The subwoofer is hooked up to the receiver with a single interconnect cable. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management saporiviafrancigena.com: Steve Guttenberg. Jun 04,   The best way to hook up my subs.? I have two 15 inch. Kicker subs. and a Watt Power Accoustic amp What is the best way to hook the subs up to the amp and also the amp is a 2 channel and the subs are single voice saporiviafrancigena.come told me that hooking them up parelle would be the best way but i dont know how to do that can someone explane that.

That would be a cable not necessarially coaxial with RCA plugs on the end. As for the how to connect it, use the receiver's subwoofer output like the others have said. You control the crossover and such via the receiver and, if you can't turn off the sub's internal crossover, turn it to the highest frequency it allows.

How 2 hook up a active subwoofer to a receiver or integrated amp with no subwoofer pre out on unit

I'd think the Y would add another potential for noise. Polk's recommendation to hook it up like that does not apply when using a receiver with bass management.

consider, that you

That setup is intended for small sattellite speakers that need to be crossed very high or in a stereo, full range setup. Hooking it up inline means you defeat the purpose of having bass management in the receiver and really that method more or less hasn't applied since the mid 90s, not unlinke many of their sub designs.

You must log in or register to reply here. Latest posts. Coronavirus Latest: Swerd 1 minute ago. The Steam Vent.

there can

Latest: AcuDefTechGuy 2 minutes ago. I want to incorporate a sub in an old 2-channel music system, please advise.

good question much

Latest: BeeTee 2 minutes ago. Suggestions to improvedownstairs tv room Latest: Kingnoob 7 minutes ago. Beginners and Audiophytes. In the end, it comes down to what sounds best to you, given your equipment and your individual tastes.

very valuable

Is this normal? Why should you buy a subwoofer? What is the best way for me to hook up my subwoofer?

Can you hook up two subwoofers to a mono amp. If you wish to wire them in series, run a single wire from the negative terminal of the first sub to the positive terminal of the second sub. Two subs up an amplifier, you'll need only a set of speakers. With two subs, this is a great way to get the pounding bass you're looking for%. Mar 24,   channel audio (e.g. media found on DVD discs or from cable television) has a dedicated channel output (the '.1' part) with bass-only content that is best reproduced by a subwoofer. Setting this up merely requires connecting the LFE (or subwoofer output) jack on the receiver/amplifier to the 'Line In' or 'LFE In' jack on the saporiviafrancigena.com: Gary Altunian. Dec 18,   Hi I have 2 10 inch wat sapphire legacy single coil subs and I have a four channel amp what's the best way to hook up the four channel amp to the 2 10 inch single coil (I believe)4 Ohm's Legacy Subs for best bass ASAPReviews:

General Sub Controls and Explanations Where is the best place to put a subwoofer in my room? Replacing a subwoofer amplifier The optimal connection is to use the RCA Phono "sub" or "woofer" line out found on home theater receivers and pre-amps.

congratulate, your



Facebook twitter google_plus reddit linkedin

0 thoughts on “Best way to hook up subs and amp

Leave a Reply

Your email address will not be published. Required fields are marked *